The Land Rover Series 2 Club Forum

Advanced search  

News:

  It's getting sunnier ...                                                 

Pages: [1]   Go Down

Author Topic: Anyone know [or can easily measure] the dimensions of part 331675  (Read 457 times)

gvo416j R.I.P.

  • Gear shifter
  • ****
  • Offline Offline
  • Location: Matlock
  • Posts: 347
  • .:

Hi, I find myself short of part number 331675 which is the horizontal aluminium insert for the 3/4 canvas.

I have a pair of nos vertical pieces [the more complicated parts] but am short of the horizontal piece which joins them.

From memory it is a simple length of aluminium strip the same width and thickness as the verticals but I do not know the length or position of the pair of 3/8"[?] holes in it.

Supposedly Craddocks have them in stock [I wouldn't take a bet on it :stars] and Exmoor trims' website says they sell them separately but they are a bit expensive for a simple strip of Aluminium.

Don't suppose anyone has one laying about which they could measure for the position of the holes  [ on the c/l of the aluminium strip ?, centre to centre of the pair] ?
Logged

Gibbo103

  • S2C Member
  • Hub seal tester
  • *
  • Offline Offline
  • Location: Newton Longville and Lower Bodham
  • Posts: 159
  • Member no : 5172
  • .:
Re: Anyone know [or can easily measure] the dimensions of part 331675
« Reply #1 on: May 09, 2021, 09:51:50 PM »

Can’t tell the dimension of the original hole centres, but when I made mine, I just cut the top strip to length to suit the hood, laid the vertical pieces over it to form the corners and marked through the holes.
Logged

Simon1959

  • S2C Member
  • Gear shifter
  • *
  • Offline Offline
  • Location: North West ish
  • Posts: 391
  • Member no : 6929
  • .:
Re: Anyone know [or can easily measure] the dimensions of part 331675
« Reply #2 on: May 09, 2021, 10:18:10 PM »

Hi, I find myself short of part number 331675 which is the horizontal aluminium insert for the 3/4 canvas.

I have a pair of nos vertical pieces [the more complicated parts] but am short of the horizontal piece which joins them.

From memory it is a simple length of aluminium strip the same width and thickness as the verticals but I do not know the length or position of the pair of 3/8"[?] holes in it.

Supposedly Craddocks have them in stock [I wouldn't take a bet on it :stars] and Exmoor trims' website says they sell them separately but they are a bit expensive for a simple strip of Aluminium.

Don't suppose anyone has one laying about which they could measure for the position of the holes  [ on the c/l of the aluminium strip ?, centre to centre of the pair] ?

I have the full set laid on the bench awaiting fitting. I can provide you with some dimensions tomorrow.
Logged

Simon1959

  • S2C Member
  • Gear shifter
  • *
  • Offline Offline
  • Location: North West ish
  • Posts: 391
  • Member no : 6929
  • .:
Re: Anyone know [or can easily measure] the dimensions of part 331675
« Reply #3 on: May 10, 2021, 09:15:14 AM »

Here you go, hope its legible.

Logged

gvo416j R.I.P.

  • Gear shifter
  • ****
  • Offline Offline
  • Location: Matlock
  • Posts: 347
  • .:
Re: Anyone know [or can easily measure] the dimensions of part 331675
« Reply #4 on: May 10, 2021, 08:13:44 PM »

Thank you very much for that. Just what I required.

I was going to do as Gibbo103 suggested if nobody could help but the forum excels once again :first
Logged

Simon1959

  • S2C Member
  • Gear shifter
  • *
  • Offline Offline
  • Location: North West ish
  • Posts: 391
  • Member no : 6929
  • .:
Re: Anyone know [or can easily measure] the dimensions of part 331675
« Reply #5 on: May 10, 2021, 08:31:37 PM »

Hi there, forgot to say the holes are 7.5mm diameter
Logged

Leon

  • Chassis welder
  • **
  • Offline Offline
  • Location: Upper Hutt, New Zealand
  • Posts: 66
  • .:
Re: Anyone know [or can easily measure] the dimensions of part 331675
« Reply #6 on: May 11, 2021, 10:36:02 AM »

*&%^$, i just ordered one from Craddocks, as i didn't have the dimensions.
Logged
112602729 Fire Tender
112801540 Hard Top
28700207A 1963 2a Forward Control
1992 D90 Tdi
1993 R-R Tdi

gvo416j R.I.P.

  • Gear shifter
  • ****
  • Offline Offline
  • Location: Matlock
  • Posts: 347
  • .:
Re: Anyone know [or can easily measure] the dimensions of part 331675
« Reply #7 on: May 18, 2021, 01:01:56 AM »

Thanks again for the help with dimensions.

A couple of pics. of the [almost] finished vehicle. The first is after fitting the goalposts and gutters, hoodsticks, spare wheel well and bracket, plus wear strips on floor.

Second is tonight after its first trip away -- performed well and waterproof, unlike my old caranex which will need some Fabsil treatment before I use it again.
Logged

Davidss

  • S2C Member
  • Master of the oils
  • *
  • Offline Offline
  • Location: Matlock-ish
  • Posts: 876
  • Member no : 2241
  • .:
Re: Anyone know [or can easily measure] the dimensions of part 331675
« Reply #8 on: May 18, 2021, 11:12:48 AM »

That's looking good, congratulations.
Logged
Pages: [1]   Go Up
 

Page created in 0.055 seconds with 22 queries.