S2C Forum Archives

Advanced search  

News:

  Our new forum is open for business:-  New Forum
To use the new forum you will need to re-register.

Please don't post anything on this forum.

Pages: [1]   Go Down

Author Topic: Canvas frame work for an 88" any drawings  (Read 2160 times)

winchman

  • Gear shifter
  • ****
  • Offline Offline
    • Location: Liverpool
  • Posts: 413
  • .:
Canvas frame work for an 88" any drawings
« on: September 27, 2019, 05:50:35 PM »
We have 88" Truck top and the last owner kindly gave us an old canvas but we dont have the frame work. Would any one have any we could copy or a drawing? We have a tube bender and welder just need some guidance on dimentions
Logged

gromet

  • S2C Member
  • Hub seal tester
  • *
  • Offline Offline
    • Location: West Caister, Norfolk
  • Posts: 174
  • Member no : 1668
  • .:
  • Don't follow me I'm lost too
Re: Canvas frame work for an 88" any drawings
« Reply #1 on: September 27, 2019, 06:08:08 PM »
If you click on the photo gallery on the forum header and click on technical section you will see some pictures wittsend has put up :-\
Logged

winchman

  • Gear shifter
  • ****
  • Offline Offline
    • Location: Liverpool
  • Posts: 413
  • .:
Re: Canvas frame work for an 88" any drawings
« Reply #2 on: September 27, 2019, 06:10:33 PM »
Thanks will have a look
Logged

winchman

  • Gear shifter
  • ****
  • Offline Offline
    • Location: Liverpool
  • Posts: 413
  • .:
Re: Canvas frame work for an 88" any drawings
« Reply #3 on: September 27, 2019, 06:14:01 PM »
Tried to look but tells me I need to log in? Couldnt see any dimensions though?
Logged

Rambler

  • S2C Member
  • Hub seal tester
  • *
  • Offline Offline
    • Location: Saskatchewan
  • Posts: 138
  • Member no : 5256
  • .:
Re: Canvas frame work for an 88" any drawings
« Reply #4 on: September 29, 2019, 06:42:46 AM »
This might help from a 109”, but the forward hoop set is a bit different on a truck cab I believe.
Logged
Former custodian of:

- a 1957 Series 1, 88” with hard top
- Luna, a 1961 Series 2, 88” with full tilt (restoration completed in 2020)
- Tardis, a 1973 Series 3, 88” with hard top (last seen sunning itself in the Carolinas)

Rambler

  • S2C Member
  • Hub seal tester
  • *
  • Offline Offline
    • Location: Saskatchewan
  • Posts: 138
  • Member no : 5256
  • .:
Re: Canvas frame work for an 88" any drawings
« Reply #5 on: September 29, 2019, 06:55:40 AM »
Logged

winchman

  • Gear shifter
  • ****
  • Offline Offline
    • Location: Liverpool
  • Posts: 413
  • .:
Re: Canvas frame work for an 88" any drawings
« Reply #6 on: September 29, 2019, 07:53:29 AM »
Quote from: Rambler on September 29, 2019, 06:42:46 AM
This might help from a 109”, but the forward hoop set is a bit different on a truck cab I believe.
Thats great thanks very much.
Have to get the bender out and see what we can make
Logged

winchman

  • Gear shifter
  • ****
  • Offline Offline
    • Location: Liverpool
  • Posts: 413
  • .:
Re: Canvas frame work for an 88" any drawings
« Reply #7 on: September 29, 2019, 07:57:17 AM »
Quote from: Rambler on September 29, 2019, 06:55:40 AM
More diy info.

See

http://www.aloharovers.com/tech/109hoop.htm
Thanks again, I will let you know how we get on, its been collected yesterday and should be with us tomorrow, so then the work begins.
Logged

Rambler

  • S2C Member
  • Hub seal tester
  • *
  • Offline Offline
    • Location: Saskatchewan
  • Posts: 138
  • Member no : 5256
  • .:
Re: Canvas frame work for an 88" any drawings
« Reply #8 on: September 29, 2019, 08:04:45 AM »
Best of luck to you  :cheers
Logged
Pages: [1]   Go Up
« previous next »
 

Page created in 0.048 seconds with 22 queries.