S2C Forum Archives

Advanced search  

News:

  Our new forum is open for business:-  New Forum
To use the new forum you will need to re-register.

Please don't post anything on this forum.

Pages: [1] 2 3 ... 12   Go Down

Author Topic: What you did with your Series 2s in May ...  (Read 26011 times)

Wittsend

  • Administrator
  • Lord of the Bearings
  • ****
  • Offline Offline
    • Location: Norwich
  • Posts: I am a geek!!
  • .:
What you did with your Series 2s in May ...
« on: May 01, 2020, 12:03:23 AM »
Anything ... ???

Logged
Who's a then ?
 

Porkscratching

  • Master of the oils
  • *****
  • Offline Offline
    • Location: London
  • Posts: 937
  • .:
  • I know nothing!...nothing..!
What you did with your Series 2s in May ...
« Reply #1 on: May 01, 2020, 10:41:30 AM »
Unfortunately nothing more interesting than fired it up and went down the road to get a few bits and bobs...
Ps that's a very shiny engine Mr W, tho you didn't paint the exhaust manifold.! :-X
Logged

martinthefirst

  • S2C Member
  • Gear shifter
  • *
  • Offline Offline
    • Location: Croydon, Surrey
  • Posts: 301
  • Member no : 4519
  • .:
What you did with your Series 2s in May ...
« Reply #2 on: May 01, 2020, 11:54:29 AM »
Took some french beans and sweet corn that SWMBO had started off in the greenhouse down to the allotment. Unfortunately had a traffic light race with a Range Rover on the way. When I opened the door , all the sweetcorn fell out :-[, only lost one of them .  (Sweetcorn, not te**??cles)
Logged
Land Rover Series IIA 1964, 3.9 V8, Designa chassis
Morris Minor Convertible 1961

Betsy1969

  • S2C Member
  • Master of the oils
  • *
  • Offline Offline
    • Location: South Yorkshire
  • Posts: 827
  • Member no : 5469
  • .:
What you did with your Series 2s in May ...
« Reply #3 on: May 01, 2020, 12:27:43 PM »
Put oil in the transfer box and started up for the first time since lockdown started , then drove out of garage. Must be my imagination but everything seems quieter just reversing one car length .
Logged

GRMac

  • S2C Member
  • Gear shifter
  • *
  • Offline Offline
    • Location: Lincolnshire
  • Posts: 438
  • Member no : 6064
  • .:
What you did with your Series 2s in May ...
« Reply #4 on: May 01, 2020, 02:01:32 PM »
Made a hot water take off for the arctic heater :RHD
Logged

Gres

  • S2C Member
  • Hub seal tester
  • *
  • Offline Offline
    • Location: Ramsbottom
  • Posts: 152
  • Member no : 4439
  • .:
What you did with your Series 2s in May ...
« Reply #5 on: May 01, 2020, 03:08:11 PM »
As I am currently marooned at my girlfriend's house I discreetly hid this under the frozen peas in preparation for speedi sleeving tomorrow!
Logged

Wittsend

  • Administrator
  • Lord of the Bearings
  • ****
  • Offline Offline
    • Location: Norwich
  • Posts: I am a geek!!
  • .:
What you did with your Series 2s in May ...
« Reply #6 on: May 01, 2020, 06:03:03 PM »
Good man ...  :cheers



Looks like it could do with one.
Logged

oddjob

  • S2C Member
  • Lord of the Bearings
  • *
  • Offline Offline
    • Location: Ealing, West London.
  • Posts: 23596
  • Member no : 2153
  • .:
What you did with your Series 2s in May ...
« Reply #7 on: May 01, 2020, 06:20:49 PM »
It'll smell of E-pea 90...





sorry!
Logged
We’re all here because we’re not all there.

Peter Holden

  • S2C Vehicle Registration Officer
  • Director
  • Lord of the Bearings
  • *
  • Offline Offline
    • Location: Adlington Lancashire
  • Posts: 3977
  • Member no : 4528
  • .:
  • Peter Holden
What you did with your Series 2s in May ...
« Reply #8 on: May 01, 2020, 08:25:10 PM »
Not done but received today from Gordon and Wendy Lowe a "*&%^$ knuckles" badge made from an old door hinges and a spanner.  Also in today's post a door latch bought from eBay for £10 and it is almost new.  Just like a birthday.

Peter
Logged
A Yorkshireman on missionary duty in Lancashire

andrewR

  • S2C Member
  • Master of the oils
  • *
  • Offline Offline
    • Location: Glasgow
  • Posts: 587
  • Member no : 6506
  • .:
What you did with your Series 2s in May ...
« Reply #9 on: May 01, 2020, 09:29:16 PM »
Made an incompetent attempt to change my rear diff pinion oil seal.
Dropped off the prop shaft and the drive flange and then got in a panic because I thought the pinion bearing had collapsed, as it was all wobbly.
Of course it is fine, it just goes loose when the drive flange comes off.. but I didn't think straight at the time.
So I dropped the diff out to try and see what was going on...
Then I worked out the bearing was fine of course.
Then I made a hash of putting the new seal in - and got confused about which way I was even trying to put it in.
And I don't have a new diff gasket handy to put the diff back in again when I get the seal in.. will have to wait for one to arrive in the post.
What an eejit!
On the plus side, having drained the diff of oil, it was fairly manky and I can give it a good clean out of sludge if there is any.
So it will get nice new oil as well as a seal, and the cogs still look AOK.
Logged
Andrew

Gres

  • S2C Member
  • Hub seal tester
  • *
  • Offline Offline
    • Location: Ramsbottom
  • Posts: 152
  • Member no : 4439
  • .:
What you did with your Series 2s in May ...
« Reply #10 on: May 02, 2020, 02:13:05 PM »
Quote from: oddjob on May 01, 2020, 06:20:49 PM
It'll smell of E-pea 90...





sorry!

Easy pea-sy, job successful and I didn't get caught  :wooly-jumper
Under £11 for the sleeve from eBay was a bonus.
Logged

kempus

  • S2C Member
  • Chassis welder
  • *
  • Offline Offline
    • Location: Worcester
  • Posts: 16
  • Member no : 2147
  • .:
What you did with your Series 2s in May ...
« Reply #11 on: May 02, 2020, 07:37:27 PM »
More work on the tub - 2nd rear panel replaced, brackets added, countersink rivet holes filled.  I have now got to template some reinforcing brackets to strengthen the front and back of the wheel arches.  Also, ran out of rivets (again...)

FYI - to replace floor, front reinforcing strip and rear panels needs around 200 counter sink rivets...

Logged

Alice B

  • S2C Member
  • Chassis welder
  • *
  • Offline Offline
    • Location: Tain
  • Posts: 67
  • Member no : 3144
  • .:
What you did with your Series 2s in May ...
« Reply #12 on: May 02, 2020, 07:59:08 PM »
Oiled the springs and painted the rear axle.
Logged

gcc130

  • Gear shifter
  • ****
  • Offline Offline
    • Location: Wiltshire
  • Posts: 390
  • .:
What you did with your Series 2s in May ...
« Reply #13 on: May 02, 2020, 09:16:36 PM »
Finally managed to release our 11a from the garage today, having put it away in disgust on 21st July ‘18!
Logged

Tom

  • Moderator
  • Master of the oils
  • ***
  • Offline Offline
    • Location: Evesham, Worcestershire
  • Posts: 951
  • Member no : 3375
  • .:
What you did with your Series 2s in May ...
« Reply #14 on: May 02, 2020, 09:43:20 PM »
Quote from: Gres on May 01, 2020, 03:08:11 PM
As I am currently marooned at my girlfriend's house I discreetly hid this under the frozen peas in preparation for speedi sleeving tomorrow!
Do you happen to have a link to the speedi sleeve you used Gres?
Logged
Pages: [1] 2 3 ... 12   Go Up
« previous next »
 

Page created in 0.051 seconds with 22 queries.